Clark & Sons Roofers LLC logo Clark & Sons Roofers LLC
TPO Roofing

TPO roofing in Austin built for sun and standing water

White TPO is the default low-slope roof in Austin for a reason: it reflects the sun that cooks other membranes, and its heat-welded seams hold up to our cloudbursts. We install and repair TPO roofs on commercial buildings and modern low-slope homes. Call for a free inspection.

Service overview

What TPO Roofing in austin actually involves

TPO, or thermoplastic polyolefin, is a single-ply membrane welded into a continuous sheet. The white surface reflects solar heat, which matters under Austin's energy code for low-slope roofs, and the welded seams are stronger than the membrane itself when they are done right. The Austin-specific enemies are ponding water, which tests every seam, and oak debris, which clogs the drains that keep ponding away. A TPO roof needs a drainage plan and seam discipline, not just a white surface. We check slope, drains and scuppers before recommending any membrane work, because a membrane over bad drainage is money spent twice.

! Common warning signs

Seam splits at penetrations and curbs

TPO seams fail first where the membrane changes direction: at curbs, pipes and parapet walls. UV and heat cycling open a cold weld over time, and the split lets water under a membrane that looks sound from above.

Ponding water stressing the membrane

Water standing on a TPO roof after a storm stresses seams and feeds algae. We check slope to drain and drain capacity before recommending membrane work, because ponding is a drainage problem first.

Punctures from debris and foot traffic

Hail, falling branches and rooftop foot traffic puncture TPO. A small puncture is a cheap repair if it is found early and an expensive leak if it is not. We walk the whole field on every inspection, not just the obvious spots.

Scope of work

What's included in a TPO roof install

A TPO project is a welded system, not a roll of membrane. Below is what a full TPO installation with us covers as standard.

  • 01

    Drainage survey and slope check

    We map how water moves across the roof, check every drain, scupper and overflow, and measure the slope to drain. The drainage plan comes before the membrane choice.

  • 02

    Deck, insulation and cover board

    We inspect the deck, replace wet insulation, and lay a cover board where the roof needs puncture protection. Wet insulation holds water against the deck and has to come out before the new membrane goes down.

  • 03

    Membrane installation and heat welding

    The TPO membrane is laid and its seams are heat-welded into a continuous sheet, then probed to confirm the weld. A weld that has not been probed is a guess, and we do not guess on seams.

  • 04

    Flashing, drains and terminations

    Parapet flashing, drain baskets and terminations go on as part of the system. If the primary drain clogs with oak debris, the overflow path has to work, and we test that path rather than assuming it.

Why Austin owners choose white TPO

White TPO reflects the heat that ages other membranes, its welded seams are the strongest part of the system when done right, and it meets the cool-roof expectations Austin sets for low-slope roofs. Call and we will walk your roof and show you where the water goes.

Call (469) 779-9940

Tools and methods we use on TPO roofs

Heat welder

Welds TPO seams into a single continuous sheet. Seams are welded at the right temperature and speed, then probed to confirm the bond.

Seam probe

A simple tool with an important job: it finds the cold weld before the rain does. Every seam we weld gets probed before we leave the roof.

Moisture meter

Finds wet insulation and decking under a membrane that looks sound from above. Wet insulation has to come out, or it rots the new roof from below.

Fall protection harness

Low-slope roofs still have edges, openings and parapets. Every crew member near an edge wears a harness anchored to a proper point.

Local execution

TPO is the Austin commercial default, and it shows up on the low-slope sections of modern infill too. The 2024 code family, effective 10 July 2025, governs new work, including cool-roof requirements for low-slope roofs, and commercial re-roofs have no permit exemption in Austin, unlike like-for-like residential work. Our cloudbursts are the real test: the 28 May 2025 storm dropped about two inches of rain in under an hour, and a TPO roof lives or dies on whether its drains kept up. Oak leaves, acorns and juniper clog those drains, so maintenance is part of the system. If your TPO roof ponds after rain, read why your roof leaks after heavy Austin rain and how to spot roof leak signs before they damage your attic, then call us for a free inspection.

Recent work

TPO seams: the weld is the roof On a TPO call we probe the seams, especially at curbs and parapets, and check for cold welds that open under heat cycling. A failed seam is a small repair if it is found early.
Ponding on a TPO roof Where water stands we map the slope, check the drains, and look for sagging deck or crushed insulation underneath. The fix is usually drainage and slope, not a new membrane.
Attic insulation with fiberglass batts between joists in a clean attic
Response time
Response time

Flat roof help when you need it

We answer the phone, even after a storm

After a major rain event, a TPO roof's question is whether the drains kept up. We prioritise roofs with standing water and active leaks, and we carry drain stock and temporary patching on the truck. We are open 24 hours, every day, so a leak at night still gets a voice on the phone, and we give you a straight answer on timing when you call.

24hr
Repair call response

How our TPO installation process works

1

Roof inspection and moisture scan

We walk the roof, probe the seams, scan for wet insulation, and map the drainage. You get a written scope that says plainly whether the roof needs drainage work, a repair, or a replacement.

2

Tear-off and deck repair

Where the membrane comes off, we strip to the deck, replace wet insulation and soft decking, and prepare the surface. Wet insulation left in place will rot the new roof from below.

3

Insulation and cover board

New insulation and a cover board go down before the membrane, giving the TPO a flat, protected surface. This layer is what keeps foot traffic and hail from puncturing the new roof.

What shapes the cost of TPO roofing in Austin

We do not publish prices, because no two TPO roofs price the same and a number quoted without seeing the roof would be a guess. Call (469) 779-9940 for a free inspection and we will walk the roof, probe the seams and map the drainage, then give you a written estimate. The factors below are what move that estimate.

01

Roof size and penetration count

Square footage drives membrane material, and every curb, pipe and rooftop unit adds detailing labour. A roof crowded with equipment takes longer than an open deck.

02

Insulation and deck condition

Wet insulation and soft decking have to come out before the new membrane goes on. We scan for moisture at the inspection so the estimate reflects the real scope.

03

Drainage and slope work

If the roof ponds, the fix may include tapered insulation or new drains. We map the drainage first so the estimate covers the job that actually solves the problem.

Rated by Austin homeowners

Clark & Sons Roofers LLC is rated 4.9 out of 5 across 36 Google reviews. Call (469) 779-9940 to book a free inspection. — Google rating

TPO Roofing questions, answered

How do I get a price for TPO roofing in Austin TX?

Call (469) 779-9940 for a free inspection. We walk the roof, probe the seams, scan for wet insulation and map the drainage, then give you a written estimate. We do not quote a price over the phone for a roof we have not seen.

Is TPO good for Austin heat?

Yes. White TPO reflects solar heat, which is why it is the Austin commercial default for low-slope roofs and fits the cool-roof expectations the city sets for them. The membrane still needs its seams probed and its drains kept clear.

How long does a TPO roof last in Austin?

It depends on the membrane thickness, the seam quality, the drainage and the maintenance. A TPO roof that drains well and gets its seams checked regularly lasts far longer than one that ponds. Ponding and UV are the two things that shorten its life here.

Why is my TPO roof leaking at the seams?

Because seams fail first where the membrane changes direction, at curbs, pipes and parapet walls. A cold weld opens under heat cycling and lets water under a membrane that looks sound. We probe every seam on an inspection to find the failed ones.

!

Get your TPO roofing in Austin inspected this week

Ponding water and open seams do not fix themselves. Call us for a free inspection with photos and a written scope. We answer the phone around the clock.

Call Now: (469) 779-9940